Immersivt system med 1234AC, S360A och 7382A

Den här lösningen kombinerar referenslyssning av hög kvalitet och generös SPL för stora dubbningsstudior. Använd 1234AC som LCR, kompakta S360 för surroundljud och ljud ovanifrån och 7382 för att komma ner till 15 Hz.


Produkter i detta system

8 × S360 SAM™ Studio Monitor
3 × 1234AC SAM™ Studio Monitor
1 × 7382A SAM™ Studio Subbas

Produkter i detta system

S360 SAM™ Studio Monitor

SPL

118 dB

Frekvensomfång

36 Hz - 22 kHz (-6dB)

Mått

H 530 x W 360 x D 360 mm, with Iso-Pod™ (vy i tum)

1234AC SAM™ Studio Monitor

SPL

125 dB

Frekvensomfång

29 Hz - 21 kHz (-6dB)

Mått

H 489 x W 1210 x D 412 mm, (vy i tum)

7382A SAM™ Studio Subbas

SPL

129 dB

Frekvensomfång

15 Hz - 100 Hz (-6dB)

Mått

H 625 x W 1400 x D 558 mm, (vy i tum)

Nyckelteknologier

Smart Active Monitor-system (SAM™)

Tekniken Directivity Control Waveguide (DCW™)

Aktiva delningsfilter

Intelligent Signal Sensing (ISS™)

Tekniken Laminar Integrated Port (LIP™)

Skyddskretsar

Optimerade förstärkare

Rumskorrigering

Mångsidiga monteringsalternativ

Bass Management

Hitta Din Återförsäljare

Ange din stad för att hitta din närmaste Genelec-återförsäljare

Dokumentation

FAQ

The Classic 8000 Series monitors have an analogue input. The 7200 Series SAM subwoofers have AES/EBU digital outputs only. However, other 7300 Series SAM subwoofers have analogue inputs and outputs and can be used also with analogue monitors.

Which SAM™ Products You Are Going to Mix With the Classic 8000 Series?
Mixing 8000 Series and SAM™ monitors is not recommended

We do not recommend mixing Classic 8000 Series monitors with SAM™ Monitors.
If the analogue input sensitivity of 8000 Series and SAM™ Series monitors are the same, Genelec SAM™ Monitors exhibit a slightly larger latency (< 5 ms) than 8000 Series monitors. Therefore Classic 8000 Series and SAM™ Series monitors should not be mixed in a stereo pair or multichannel setup.

It is alright to mix Classic 8000 Series with SAM™ Subwoofers

However, it is okay to mix the Classic 8000 Series monitors with SAM™ Subwoofers. Any Classic 8000 Series monitors can be used with SAM™ Subwoofers, in any stereo or multichannel setup.

Setting the room response calibration controls

Genelec monitors are calibrated flat in anechoic free field conditions. When the monitor is placed in a room close to walls or other boundaries, the low frequency output of the monitor increases. To achieve a flat low frequency response an adjustment of typically -4 dB on the bass tilt control is used. Genelec also provides a bass roll-off control to compensate for any remaining excessive LF energy around the low cut-off frequency.
Genelec GLM AutoCal can implement a more precise compensation after measuring the acoustic effects produced by the monitor’s installation location.

Differences in room reverberation time and listening distance can lead to changes being required in the treble region so treble tilt is fitted to most of the models in the Genelec range.

In three-way monitors and large main systems there are additional driver controls for the bass level, mid level and treble level which enable very fine adjustment of the frequency response so that the monitors can be placed in many different listening environments, whilst still achieving a consistent and neutral sound reproduction.

The best way to set the room response controls of a Genelec monitor is by taking an acoustical measurement at the listening location, using a measurement system for those products that offer local controls (DIP switches) on the monitor or subwoofer, or by using GLM AutoCal for the SAM™ (Smart Active Monitoring) products.